In the electronic and microfabrication industry, die separation is one of the most critical steps in producing an undamaged, stand-alone micro-scale device. For silicon based devices, it is the predominant step governing resistance to die failure...
A combination of three techniques – high resolution micro computed tomography (micro CT) scanning, Archimedes-based volume fraction measurement and serial sectioning or milling – were used to determine the volume fraction, trabecular thickness,...
Simplified modeling generates a great deal of interest in the area of crashworthiness analysis. Modeling methods used to create simplified computer models for crashworthiness have been well developed. In advanced simplified models, researchers...
In order to satisfy customer expectations, a ground vehicle must be designed to meet a broad range of performance requirements. A satisfactory vehicle design process implements a set of requirements reflecting necessary, but perhaps not sufficient...
Microelectromechanical systems; Biotelemetry; Strains and stresses--Measurement
Lumbar arthrodesis or spinal fusion is usually performed to relieve back pain and regain functionality from ruptured discs, disc degenerative disease, trauma and scoliosis. Metal rods are often fixed to the spine with screws or hooks, while fusion...
Bi-stable buckled MEMS (micro-electromechanical systems) diaphragms have a myriad of uses in the MEMS field for their large out-of-plane deflections. Buckling is a phenomenon brought upon by a compressive stress. Diaphragms are large aspect ratio,...
A Physics doctoral project seeks to reduce the uncertainty of inaccurate visual bridge inspections by producing a remote sensor program to determine and monitor the changes in health of a specified bridge. The Eastern Parkway Bridge was determined...
Over the last 15 years, researchers have explored the use of piezoresistive microcantilevers/resonators as gas sensors because of their relative ease in fabrication, low production cost, and their ability to detect changes in mass or surface stress...
Wheelchairs--Design and construction; Dogs--Equipment and supplies; Dogs--Health; Veterinary physical therapy
Hind limb paralysis may occur in dogs for a variety of neurological or musculoskeletal reasons. For dogs with limited mobility their lack of ability to ambulate can have a great impact on their physical and mental health. Canine wheelchairs can...
High dynamic range imaging involves imaging at a bit depth higher than the typical 8-12 bits offered by standard video equipment. We propose a method of imaging a scene at high dynamic range, 14+ bits, to detect motion correlated with changes in...
Modular hip implants are currently being used in total hip arthroplasty revision procedures because it is common to have little or no bone left in the proximal region of the femur and it is difficult to accurately size implants based off of...
Law and legislation--Kentucky; Law and legislation--Virginia; Constitutions--Kentucky; Constitutions--Virginia
Littell's Statute Law of Kentucky, published from 1809-1819, has the first critically edited compilation of Kentucky statutes. It has long been recognized by lawyers as one of the founding documents of state law and by historians of early Kentucky...
The Louisville Leader was an African-American newspaper published from 1917 to 1950 by I. Willis Cole in Louisville, Kentucky. There is a tear down the center of each page of this issue.
The Louisville Leader was an African-American newspaper published from 1917 to 1950 by I. Willis Cole in Louisville, Kentucky. This issue says Vol. 30. No. 41. but is actually Vol. 30. No. 42. This issue is four pages and there is a crease across...
Identity (Philosophical concept) in art; Museum techniques; Museum exhibits--Social aspects; Museums--Social aspects
This thesis paper expands upon the aspects of identity and power explored in the exhibition that I curated, entitled "Being & Making: Artists Investigating Identity," at the Speed Art Museum. The developments on topics of identity...
Thirty smokers were solicited from the Wichita, Kansas community via the newspaper and broadcast media for a stop-smoking project. The volunteers were assigned to one of two treatments: double smoking or a modification of Von Dedenroth's (1964)...
Athletic cleated shoe failures are commonplace to competitive-level ultimate
frisbee players. Currently, there are no athletic cleated shoes designed for the sport of
ultimate frisbee; players generally choose between football or soccer cleated...
Every man is to a greater or less degree a product of the influences surrounding his life. The more commonplace minds of the race, no doubt, are chiefly affected; and occasionally we find a man or woman of so keen an intellect, so striking an...
Integrated circuits--Design and construction; Integrated circuits industry--Technological innovations
Lithographic processes for printing device structures on integrated circuits plays a major role in the semiconductor industry. This project aims at designing and fabricating a programmable mask for a direct write lithography system which can...
